Plasterers in Killingbeck, East Leeds
Reskimming, ceiling replacement and repairs for the semis and newer homes of Killingbeck, either side of York Road and down towards Halton Moor.

Killingbeck · LS14
York Road semis and later housing
Killingbeck sits along York Road on the eastern side of Leeds. A lot of the housing here is inter-war and post-war semis, laid out on estate roads such as Killingbeck Drive and the streets that run down towards Halton Moor. More recent homes have been built on land nearby, so the area mixes mid-century brick houses with much newer properties.
The older semis were usually built in brick, plastered internally with a backing coat and finish, and given plasterboard or lath ceilings depending on when they went up. The newer homes are generally dry lined with plasterboard throughout. Many of the older houses have been through several rounds of improvements, and the plaster shows it, with patches, chases and old finishes that no longer line up.
Ceilings and walls that have had their day
Ceiling replacement is a regular request in Killingbeck. Older ceilings that are cracked across, sagging between joists or covered in heavy texture can be overboarded with new plasterboard and skimmed. Where a ceiling is badly damaged or the joists need attention, it may make more sense to take it down and fit new board. Textured coatings are sample-tested before any ceiling is disturbed.
On walls, a reskim sorts out the uneven surfaces left by years of filler and patching. Before skimming we tap round every wall, and any hollow areas are cut out and patched or replastered so the new finish has a solid base. Damp patches on outside walls need their cause found and fixed first, whether that is a gutter, a cracked render or a plumbing leak.
Getting the work done with minimal fuss
Semis along the estate roads generally have drives or front gardens, which gives room to unload and mix outside. Ceiling work is dusty, particularly taking a ceiling down, so we clear or cover the room fully, seal the door and protect the landing or hall. Overboarding is cleaner and quicker, which is one reason it is often the preferred option.
First comes a visit to look at each room and the condition of the ceilings from below. We will tell you whether overboarding or replacement is the better route and why. The written quote lists each room and the work proposed. If you are planning new lighting, it is worth getting cables in place before the ceiling is boarded.
Services
Most asked-for in Killingbeck

Skimming & reskimming
A thin, hard new face on walls and ceilings that are sound underneath but look tired, patched or lumpy.
See the service
Ceiling repairs & replacement
Cracked, sagging, stained or brought down by a leak.
See the service
Plasterboarding & dry lining
New stud walls, boarded ceilings, insulated linings and dot and dab.
See the serviceAlso in Killingbeck
Everything else we do
Next door
Areas nearby
FAQs
Plastering in Killingbeck: questions
Should my Killingbeck ceiling be overboarded or replaced?
If the existing Killingbeck ceiling is firmly fixed and only cracked or textured, overboarding and skimming is usually quicker and cleaner. If it is sagging badly, loose from the joists or water damaged, taking it down and fitting new board is the better option. We check at the visit and explain which suits your ceiling.
Can you plaster around new downlights?
Yes. It is best if your electrician runs the cables first. We board and skim the ceiling, and the electrician cuts the holes and fits the lights afterwards, or we can leave marked positions if you prefer.
How much disruption does replacing a ceiling cause?
Taking down an old ceiling is dusty, so the room needs clearing and the door sealing. Once the old material is out, boarding and skimming are much cleaner. Overboarding avoids most of the mess, which is why we suggest it where the existing ceiling is sound.
Do you work on the newer houses around Killingbeck as well?
We do. Newer Killingbeck homes are usually dry lined, and the typical jobs are cracked board joints, popped screws, damaged corners and making good after alterations. These are generally small repairs finished with a skim where needed.